Workholding Solutions

News and Links

Upcoming Shows | News | Releases | Articles | Links | Tip of the Month | New Workholding and Accessories | Sitemap

Articles

Falcon Precision Industries, Inc. Uses New Kurt VB 5AX100 Schenke 5.1 Clamping System To Eliminate Special Holding Fixtures For Its Short Run Aerospace Component Machining – Allows Single Setup, Five-Axis Milling, Drilling And Face-Milling Of Exotic Materials With High Clamping Rigidity

Setup Time Reduced 50 Percent At Adaero Precision Components Ltd.
Using VB DockLock® Zero-Point Workholding System – 30 Minute Setup Savings Impacts Profitability

Omnitool, Inc. Reduces Machining Center Need From 2 Machines To 1 Using New Kurt VB 5X100
Schenke 5.1 Clamping System -- 3D Roughing And Face-Milling Operations Performed At 270 In/Min

Kurt's Ductile Iron ClusterTowers® Provide Needed Clamping Rigidity To Hold 0.001 Tolerances
For Roberts Automatic Products --- Kurt Setup Replaces Aluminum Towers

Super Torquer Reduces Machined Clutch System Component Costs By 65 Percent Utilizing Four
Kurt HD Vises -- Setup With Quick Change Jaws Hold 40 Components For Highest Density Machining

Vincent Precision Machining Improves Per Part Setup Time From 5 Minutes To Less Than A Minute
By Changing To Kurt HDL Vises With Ductile Iron Bodies - Improves VMC "In-The-Cut" Time

A More Palletable Method Of Workholding - Kurt Custom Made 6 Inch Pallet Vise
Insures ± .0005 Accuracy And Reduces Setup Time By 30 Minutes While Increasing Productivity

Combining Flexible Kurt CarvLock™ ClusterTower™ Setups With DoubleLock Vises
And Dedicated Fixtures Maximize Machine Output At SPX Service Solutions

Twin Kurt Vise Setup Clamps 1500 Lb. Hammer Dies Vertically For Precision Machining
-- Setup Time Reduced By 50 Percent Over Dedicated Fixtures At Impact Forge, Inc.

Tescom Corporation Improves Productivity 50 Percent - Reduces Workholding Part Loading Time
From Minutes To Just Seconds By Changing To New Kurt HD Vises From Standard Single Station Vises

Precise Products Improves Productivity 50 Percent; Reduces Workholding Changeover From 5 Minutes To Just 1 Minute Using New Kurt HD Vises

Ten Cluster Tower Workholding System From Kurt Utilizes Stepped Jaws Allowing
Machining On Three Sides Of Each Part -- -- Increases Output While Reducing Setup Time

Painted Feather Precision Improves Productivity By Adding Kurt Vise Towers - Rigidity Helps Greatly Reduce Scrap

Adding A Flexible Kurt™ CarvLock™ ClusterTower™ Setup Used Alongside Of A Dedicated Fixture Maximizes Machine Output While Providing Flexible Workholding

High Density Workholding Using New Serrated Mounting Components Key To Quick Turnaround At JEM Technical -- Kurt Cluster Tower FMS Provides Maximum Setup Versatility While Machining Center Operates Non-Stop

Twenty-Four Kurt Cluster Tower FMS Gives Choice Precision Maximum Setup Versatility While Operating Its Twin Machining Centers Non-Stop

Kurt Vise Towers With CarvLock Clamping System Provide Flexible Workholding For FMS At Teleflex (Canada) Ltd. - - Machinable Vise Jaws Have .001" Repeatability

 

9445 E. River Road NW
Minneapolis, MN 55433

Phone: 763-574-8309 | 1-877-226-7823
Fax: 612-623-3902 | 1-877-226-7828

Association for Manufacturing Technology

Workholding Product Group

 Iron Clad Warranty

Kurt Corporate | Kurt Hydraulics | Kurt Electronics | Kurt Kinetic | Kurt Chipmunk
Copyright ©2008 Kurt Manufacturing. All rights reserved. Privacy Policy | Sitemap